CFD Intermediate Courses

Price: $809

The problem numerically simulates a Skywalker-X8 UAV using ANSYS Fluent software. We design the 3-D model with the Design Modeler software. We mesh the model with Fluent Meshing software. The element number equals 928,595 and their type is polyhedra. In this simulation, FW_H and BroadBand Noise are used for acoustic modeling.

Price: $120

A 2D symmetric geometry with a structured mesh of 310,000 cells was created, refined near the projectile walls for accuracy. This project investigates the cavitation phenomenon caused by a projectile moving through water using ANSYS Fluent. A transient, pressure-based solver with the Volume of Fluid (VOF) model captures the phase interaction between liquid and vapor. The simulation analyzes velocity, pressure, and vapor volume fraction around the projectile.

Price: $60

This project presents a CFD simulation of a solar collector designed to analyze heat transfer and fluid flow inside a U-shaped tube. The system uses water as the working fluid under steady-state conditions. The outer wall is maintained at a constant high temperature to simulate solar heating. Results show an effective temperature rise, confirming efficient thermal performance of the collector.

Price: $80

This simulation studies airflow around an airfoil placed above a sinusoidal wall using mesh motion in ANSYS Fluent to analyze aerodynamic effects. The 2D model includes an airfoil over a wavy bottom surface, divided into stationary and moving zones, with a structured refined mesh near the airfoil and wall. A transient pressure-based solver with the k–ω SST turbulence model was applied using a 55 m/s inlet velocity and mesh motion of 56 m/s for the moving zone. Velocity contours show accelerated flow over the airfoil’s upper surface, while pressure contours indicate low pressure above and high pressure below, confirming lift generation influenced by the wavy boundary.

Price: $270

This report presents a simulation that investigates the two-phase flow boiling of methanol in a heated horizontal micro-channel. The development and transition of different flow regimes (bubbly, slug, churn, and annular) along the channel were analyzed. The 2D geometry of the micro-channel was created using ANSYS SpaceClaim software. A high-quality structured mesh was generated using ANSYS Meshing software. Appropriate multiphase model settings and boundary conditions were applied to correctly simulate the evaporation process and the resulting flow patterns.

Price: $24

This transient 3D simulation models evaporation and condensation of water in a thermosyphon heat pipe using the VOF and k‑ε models. The domain, meshed with 3,900,000 elements, includes heated and cooled sections defined by heat‑flux and temperature boundaries. At t = 1.655 s, liquid accumulates in the evaporator, vapor rises to the condenser, and condensation occurs at cooler surfaces. Contours of mass transfer, liquid fraction, temperature, and velocity confirm stable phase circulation and efficient heat transport.

Price: $28

The fan geometry, consisting of six blades and three zones, was created in DesignModeler and meshed with an unstructured tetrahedral grid of about 3 million elements. Broadband noise sources were applied in ANSYS Fluent to evaluate the acoustic performance and sound power level distribution. The Multiple Reference Frame (MRF) approach was used to model the rotating zone at 3000 RPM under steady-state conditions. Results show high-pressure and velocity regions near the blade tips, leading to stronger acoustic power levels along the fan casing.

Price: $36

This project presents a CFD study based on the article “Analysis of Computational Fluid Dynamics and Particle Image Velocimetry Models of Distal-End Side-to-Side and End-to-Side Anastomoses for Coronary Artery Bypass Grafting in a Pulsatile Flow.” The objective is to reproduce and validate the hemodynamic behavior of distal-end side-to-side (deSTS) and end-to-side (ETS) anastomoses. All simulations were carried out in ANSYS Fluent using steady, laminar, and incompressible flow assumptions. The results include comparisons of velocity profiles and wall shear stress (WSS) to ensure accuracy with the reference study.

Price: $100

The centrifugal pump was modeled in ANSYS with two zones: the stationary casing and the rotating impeller. A triangular mesh with 17,536 cells was generated to discretize the geometry. The impeller was simulated using the Moving Reference Frame (MRF) approach with a rotation speed of 1500 RPM.