CFD Intermediate Courses

Price: $319

Taxi Drone Ansys Fluent Simulation involves using advanced CFD software to analyze the aerodynamic performance of urban air mobility vehicles The geometry of the taxi drone was designed using ANSYS SpaceClaim , The mesh was generated using ANSYS Meshing, resulting in a total of 2,829,977 elements The velocity inlet was set to 30 m/s with an angle of attack of 5 degrees. The rotational speed of the blades was configured with MRF method at 5000 RPM, with the upper and lower blades rotating in opposite directions.

Price: Free

Introduction to the history and evolution of simulation technologies in ANSYS Discovery Overview of GPU technology and its impact on rapid simulation and immediate feedback Introduction to real-time simulation concepts, including simplified physics and automatic meshing Exploration of GPU-accelerated computing benefits: massive parallelism, specialized architecture, and real-time updates Overview of supported physics simulations: structural, fluid, thermal, and modal analysis Introduction to automatic meshing and results visualization tools Discussion on limitations and considerations, such as simplified physics and reduced precision Integration with ANSYS Workbench for comprehensive analysis capabilities

Price: $56

This study investigates the aerodynamic performance of a turbine vane using CFD simulations with two different turbulence models The simulations were conducted using ANSYS Fluent, comparing the k-Omega SST and Large Eddy Simulation (LES) turbulence models The geometry of the turbine vane was created using ANSYS Design Modeler. The computational domain was then discretized using ANSYS Meshing, resulting in a high-resolution structured mesh of 12,634,415 elements

Price: $20

This report discusses the CFD simulation conducted for the Switchblade 300 using ANSYS Fluent software The geometry of the Switchblade 300 was created using SpaceClaim Initially, Using ANSYS Meshing, a non-conformal mesh with approximately 40 million tetrahedral cells was generated, after that We decided to change the mesh type to polyhedral in Ansys fluent to decrease the number of mesh elements from 40,000,000 to 7,000,000 The setup included a velocity inlet of 28.05 m/s, an angle of attack of 5 degrees, and a rotational speed of 5000 RPM

Price: $120

In this project, we are simulating the bubbling fluidized bed (BFB), a type of fluidized bed reactor where solid particles are suspended and agitated by the upward flow of gas The design and operation of BFBs allow for better control of temperature and reaction conditions, leading to improved efficiency and product quality in industrial processes The 2D geometry of the BFB is designed using Design Modeler software. Then, it is meshed in ANSYS Meshing. In total 26800 cells are generated. To model BFB, two Eulerian phases are defined by the Eulerian multiphase model.

Price: $319

This study focuses on the aerodynamic analysis of the Switchblade 300 using ANSYS Fluent Two scenarios are simulated: one with the rear blade stationary and the other with the rear blade in motion. The geometry of the Switchblade was created using SpaceClaim software,The meshing was performed in Fluent Meshing, utilizing a polyhedral mesh with over 7,600,000 elements The Multiple Reference Frame (MRF) approach was employed to simulate the rotating rear blade at 5000 RPM.

Price: $40

we are simulating the solar panel that is floated on the water surface,The simulation is 3D and the solar panels and performed by ANSYS Fluent. The geometry is designed using Spaceclaim software. Then, it is meshed in ANSYS Meshing. In total 479895 cells are generated. phases are modeled by Volume of Fluid multiphase model. The dynamic mesh can reproduce elements by remeshing and smoothing types. Also, the radiation is activated.

Price: $24

This study uses CFD simulation to investigate the water tank filling process The geometry of the tank was created using ANSYS Design Modeler, and the computational domain was discretized using ANSYS Meshing, resulting in over 135,000 elements The Volume of Fluid (VOF) model was employed to simulate the interaction between water and air phases A User-Defined Function (UDF) was implemented to control the time step size

Price: $15

This study investigates the displacement of a net panel subjected to water flow using ANSYS Fluent simulation. The geometry of a square net panel was created using ANSYS Design Modeler. The computational domain was then discretized using ANSYS Meshing, resulting in over 2,339,853 elements. The simulation aims to analyze the net panel's fluid-structure interaction The structural model utilized a Linear Elasticity submodel to simulate the net panel’s deformation